For Queries/Clarification

Welcome to IJASER

A Few Essentials for Publishing in this Journal

Submitted articles should not have been previously published or be currently under consideration for publication elsewhere.

Conference papers may only be submitted if the paper has been completely re-written and the author has cleared any necessary permission with the copyright owner if it has been previously copyrighted.

Briefs and research notes are not published in this journal.

All our articles go through a double-blind review process.

All authors must declare they have read and agreed to the content of the submitted article. A full statement of our Ethical Guidelines for Authors (PDF) is available.

Manuscript Submission will be sent on [email protected]

Instructions to the Authors

Title: The title of the paper should be concise and definitive (with key words appropriate for retrieval purposes).

Author Names and Affiliations: It is Journal policy that all those who have participated significantly in the technical aspects of a paper be recognized as co-authors or cited in the acknowledgments. In the case of a paper with more than one author, correspondence concerning the paper will be sent to the first author unless staff is advised otherwise.

Author name should consist of first name, middle initial, last name. The author affiliation should consist of the following, as applicable, in the order noted:

- Company or college (with department name or company division)
- Postal address
- City, state, zip code
- Country name
- Telephone, fax, and e-mail
Abstract: A short abstract (200-300 words maximum) should open the paper. The purposes of an abstract are:
(1) to give a clear indication of the objective, scope, and results of the paper so that readers may determine whether the full text will be of particular interest to them;
(2) to provide key words and phrases for indexing, abstracting, and retrieval purposes.
The abstract should not attempt to condense the whole subject matter into a few words for quick reading.
References: The references should be brought at the end of the article, and numbered in the order of their appearance in the paper. The reference list should be cited in accordance with the following examples:
[1] Ning, X., and Lovell, M. R., 2002, "On the Sliding Friction Characteristics of Unidirectional Continuous FRP Composites," ASME J. Tribol., 124(1), pp. 5-13.
[2] Barnes, M., 2001, "Stresses in Solenoids," J. Appl. Phys., 48(5), pp. 2000–2008.
[3] Jones, J., 2000, Contact Mechanics, Cambridge University Press, Cambridge, UK, Chap. 6.
[4] Lee, Y., Korpela, S. A., and Horne, R. N., 1982, "Structure of Multi-Cellular Natural Convection in a Tall Vertical Annulus," Proc. 7th International Heat Transfer Conference, U. Grigul et al., eds., Hemisphere, Washington, DC, 2, pp. 221–226.
[5] Hashish, M., 2000, "600 MPa Waterjet Technology Development," High Pressure Technology, PVP-Vol. 406, pp. 135-140. [6] Watson, D. W., 1997, "Thermodynamic Analysis," ASME Paper No. 97-GT-288.
[7] Tung, C. Y., 1982, "Evaporative Heat Transfer in the Contact Line of a Mixture," Ph.D. thesis, Rensselaer Polytechnic Institute, Troy, NY.

Paper Acceptance: The final decision on publication is made by the Editor-in-Chief upon recommendation of Editorial Board Members. If the manuscript is accepted for publication in Journal , it must not be published in any periodical elsewhere without the permission of the editorial board.

Copy Right: Each manuscript must be accompanied by a statement that it has been neither published nor submitted for publication, in whole or in part, either in a serial, professional journal or as a part in a book which is formally published and made available to the public. For the mutual benefit and protection of authors and publishers it is necessary that authors provide formal written consent to publish and transfer of before publication of the work.

Proofs: Proofs will be sent to the corresponding author and should be returned with one week of receipt. Corrections should be restricted to typesetting errors; any other corrections may be charged to the authors. Authors are advised to check their proofs very carefully before return, since the inclusion of late corrections cannot be acceptable. Corrected proofs are to be returned to the publishers.

Article Processing Charges: As an Open Access title, publishing an article in this journal requires an Article Processing Charge (APC) that will be billed to the submitting author following acceptance. Apart from this Article Processing Charge there are no other fees (for example submission charges, page charges, or color charges). The APC for the journal is $ 800.

Refund Policy: Once an article has been accepted for publication, an Article Processing Charge is due. The submitting author assumes responsibility for the Article Processing Charge, and Roman Science publications will not issue refunds of any kind.

Frequency of Publication: Two issues in a year.

Subject Category: Science (All) and Engineering (All)

Science & Engineering(All)

Quick Links